Video of Topper Xenon

At last a Topper Xenon video! You would have thought Topper would have promoted a few more of these. Anyhow here are some chaps in New Zealand sailing a Topper Xenon. They don’t know how lucky they are not having to negotiate mud banks and deal with tidal flows. It looks like they have awesome conditions down there - my only comment is – keep the boat flat! (but hey I’m in my study with a glass of wine…)

Xenon real Handicap

So just what is the handicap of a Topper Xenon??

Being a good citizen I registered it at the club when I arrived as PY1070 – just like the booklet tells me.

The Lasers which I race against are ‘officially’ PY1078 and there has been some comment in the club that the handicap PY1070 is perhaps a little low ….(or we have very good Laser sailors, or I am particularly rubbish). It has even been suggested that Topper might promote low handicaps to make their boats faster!! <gasp!>

So officially at Wivenhoe Sailing Club, Topper Xenons are now rated as PY1075. This by co-incidence is the same handicap as Brightlingsea Sailing Club uses.

In my quest for the truth, I looked at a couple of other club websites and had a laugh at Erith Yacht Club who has gone totally the opposite way and has given their Topper Xenon class a local handicap of 1035!!

I suspect that a major issue is that when we race, the Barman and I are both quite heavy fella’s and this might cause some of the apparent slowness. Read here for the weight guide lines!

That said, last Sundays race went extremely well for the Barman and I. Despite the spinnaker detaching itself from the bow sprit and the forestay accidentally not been undone when the jib was rigged, we crossed the finish line a credible 2nd just behind the lead Laser. Lessons described in the blog posts below are working.

Close Haul Tips

In my previous post I gave some hints about how best to using the cunningham to adjust tension in the luff to help point the boat - especially in light winds; it's also critical to beating the Laser sailors. On the Topper Xenon this is controlled by the helmsman so naturally I would take most interest in it.

Just to complicate things there is another rope called the outhaul and this is controlled by the crew as it is cleated off under the boom by the mast. Todate when sailing we have not touched it - just made sure it was tight - well it is my first year learning to sail after all. Guidance from Topper is as follows.....

When sailing upwind you will nearly always have the outhaul pulled quite tight but you may wish to loosen it for the downwind legs. You can pre-set the "off" position by tying a large knot (or use a ball) about an inch from the cleat when the foot is pulled tight. This means you simply have to uncleat at the windward mark and it will be in about the right place for downwind sailing. Remember to pull it back on before rounding the leeward mark!

 So next time we go out I will put 2 knots in it and report back how it works.

Xenon Rudder

A comment I have about dinghy boats is that often are not the manuals available to show you how to fix minor problems. The only knowledge source is in the collective mind of the sailing club. For example, when I snapped all the lines in my rudder (see Man Sailing ) I was left guessing as to exactly which bolt the two lines should be threaded. Well if you have this problem, look at the two pics below and this will give you a clue.

Before you get too far in re-threading your stock and tiller assembly, you need to make a decision as to which type of cord you are going to use. Yes! There are 2 types of cord; that which 'gives' a bit and that which doesn't. The cord which doesn't 'give' or stretch is generally used for halyards and the like - nothing worse than sails coming down in a race and apparently the other type is more useful for sheets.

Before the man sailing day my rudder was pulled down on a 2:1 pulley with non-stretch cord. I have made a decision that since I am likely to hit mud again that it will be a better idea to use the stretchy stuff; it's cheaper as well. It's the white cord in the image above.

Speaking of cost, I was gobsmacked by the price of a stock and tiller assembly + rudder blade. At the time of writting it is in the region of £500 - see here. To all Topper Xenon owners, look after your rudder.